2026世界杯足彩怎么买?2026美加墨世界杯足彩玩法说明与购买指南

TubesT - Import from File
  • Software Download
  • Manual
  • Video
  • Tutorial
TubesT - Import from File

Ⅰ. Overview

 

Import from File is a common method in TubesT for importing parts, and the software supports the import of various part formats.
 
 

II. How to Use

 

Step 1: Click Import from File on the left side of the main interface to enter the Import Part interface. 

 

Step 2: Select the part(s) to import. You can select a single part or multiple parts at the same time.

 

Step 3: Set the parameters according to the part type and actual requirements. Explanations of each parameter are provided below.

 

Step 4: Click Open to import the part. The imported part will be displayed in the "Parts Sidebar". If an import failure message appears, you can refer to How to Resolve Part Import Failures or Recognition Errors for troubleshooting, or manually import parts to complete the process.

 

 

III. Parameter Definitions

 

1. File Type: Displays all part formats supported for import in the current version. For a detailed introduction to each format, please refer to Details about Tube File Formats.

 

 

2. Import Excel sample file: TubesT supports batch import of *.igs, *.iges, *.sat, *.jhb, *.jhbs, *.t2t, *.ifc, *.step, *.stp, *.nc1, *.pcd, and *.stepx files via Excel, saving the time required to import parts individually and check part quantities one by one, as shown in the figure below. For details, please refer to Batch Import Parts Using Excel.

 

 

3. Extrusion

 

    • Auto: When importing a file, the software automatically reads the extrusion direction of the part.
    • X/Y/Z/sat manual: Manually adjust the X/Y/Z direction. If the preview image on the right shows that the automatically read extrusion direction does not match the actual direction, try manually changing the extrusion direction until the image preview matches the actual part.

 

4. Preview

 

    • Loading: The drawing is being read.
    • 00 × 0.00 × 0.00: No drawing has been read. Adjust some parameters or refer to the section below for troubleshooting.

    • Part Dimensions: The preview area on the right displays specification information of the imported part, for example, I-Beam 40 × 30 × 2 × 2 R2, 45° thickness 2 × length 20 in the figure below, which is used to determine whether the correct drawing has been selected.

 

 

5. Section Cut

 

    • LC profile: If the part type is channel steel, angle steel, C-shaped steel, I-beam, or other LC profile steel, this parameter must be selected. For the reason, see Profile Path.
    • One Cut: Currently, toolpaths for channel steel/angle steel include "Section Cut" and "One Cut". Section cut is commonly used. If this option is not selected, section cut is used by default, and external leadin lines and gaps are automatically generated on the part surface. If selected, the channel steel/angle steel part is cut in one continuous pass along the end-face contour, without gaps. See the figure below for the specific difference.

 

 

6. Leadin: The length of the external leadin line when a special toolpath is automatically generated.

 

7. Leadout: The length of the external leadout line when a special toolpath is automatically generated.

 

Notice: For special toolpaths entered in TubesT via Import from File, Draw Part, and other methods, the external leadin line lengths carried by default all refer to the values set here.

 

8. Select contour

 

      • Outer wall contour line / Inner wall contour line / All curves: An actual part has an outer wall contour line and an inner wall contour line. Generally, Outer wall contour line is sufficient. All curves retains all contours in the drawing (including inner and outer contours) and is generally not selected.

 

 

      • Bevel: If the part requires bevel processing, selecting Bevel will generate a bevel toolpath based on the original drawing. If this parameter is not available, you need to first go to the "Gear" in the upper-left corner of the software main interface User Settings → Machine Config  and select A axis bevel cutter for this parameter to be displayed. You can also refer to How to Enable Beveling for details on using beveling.

      • In-part shape: After selecting this option, TubesT can correctly recognize and process sheet-like parts that need to be nested in tube waste material. For specific cases, please refer to How to Process Nested Contours on the Tube Surface.

 

 

9. Identification Information (called Layer Mapping before 2026 V3)

 

Recognition Identifier: Sets whether to recognize identification information in the imported file. When selected, the software reads the identifiers in the file, and their processing method can be set to Marking, Inkjet Printing, or Not Cut. When not selected, identification information in the file is not read, and the processing method cannot be set.

Notice:

a. For identifiers in *.sat, *.stepx, *.step, and *.x2t files, Marking or Inkjet Printing can be selected.

b. For identifiers in *.t2t, *.nc1, *.rnc, and *.pcd files, only Marking is supported.

c. For *.jhb, identifier recognition is determined internally by the file and can be selected when drawing in TubeDraw. For details, please refer to  TubesT - Drawing Parts - Identifier.

 

 

Ⅲ. FAQS

 

1. How do I resolve an import failure?

 

Please refer to TubesT - How to Resolve Part Import Failures or Recognition Errors. 

 

2. How to use Import Excel sample file? 

 

Please refer to TubesT - Batch Import Parts Using Excel.

 

 

TubesT - Import from File 13061view

Ⅰ. Overview

 

Import from File is a common method in TubesT for importing parts, and the software supports the import of various part formats.
 
 

II. How to Use

 

Step 1: Click Import from File on the left side of the main interface to enter the Import Part interface. 

 

Step 2: Select the part(s) to import. You can select a single part or multiple parts at the same time.

 

Step 3: Set the parameters according to the part type and actual requirements. Explanations of each parameter are provided below.

 

Step 4: Click Open to import the part. The imported part will be displayed in the "Parts Sidebar". If an import failure message appears, you can refer to How to Resolve Part Import Failures or Recognition Errors for troubleshooting, or manually import parts to complete the process.

 

 

III. Parameter Definitions

 

1. File Type: Displays all part formats supported for import in the current version. For a detailed introduction to each format, please refer to Details about Tube File Formats.

 

 

2. Import Excel sample file: TubesT supports batch import of *.igs, *.iges, *.sat, *.jhb, *.jhbs, *.t2t, *.ifc, *.step, *.stp, *.nc1, *.pcd, and *.stepx files via Excel, saving the time required to import parts individually and check part quantities one by one, as shown in the figure below. For details, please refer to Batch Import Parts Using Excel.

 

 

3. Extrusion

 

    • Auto: When importing a file, the software automatically reads the extrusion direction of the part.
    • X/Y/Z/sat manual: Manually adjust the X/Y/Z direction. If the preview image on the right shows that the automatically read extrusion direction does not match the actual direction, try manually changing the extrusion direction until the image preview matches the actual part.

 

4. Preview

 

    • Loading: The drawing is being read.
    • 00 × 0.00 × 0.00: No drawing has been read. Adjust some parameters or refer to the section below for troubleshooting.

    • Part Dimensions: The preview area on the right displays specification information of the imported part, for example, I-Beam 40 × 30 × 2 × 2 R2, 45° thickness 2 × length 20 in the figure below, which is used to determine whether the correct drawing has been selected.

 

 

5. Section Cut

 

    • LC profile: If the part type is channel steel, angle steel, C-shaped steel, I-beam, or other LC profile steel, this parameter must be selected. For the reason, see Profile Path.
    • One Cut: Currently, toolpaths for channel steel/angle steel include "Section Cut" and "One Cut". Section cut is commonly used. If this option is not selected, section cut is used by default, and external leadin lines and gaps are automatically generated on the part surface. If selected, the channel steel/angle steel part is cut in one continuous pass along the end-face contour, without gaps. See the figure below for the specific difference.

 

 

6. Leadin: The length of the external leadin line when a special toolpath is automatically generated.

 

7. Leadout: The length of the external leadout line when a special toolpath is automatically generated.

 

Notice: For special toolpaths entered in TubesT via Import from File, Draw Part, and other methods, the external leadin line lengths carried by default all refer to the values set here.

 

8. Select contour

 

      • Outer wall contour line / Inner wall contour line / All curves: An actual part has an outer wall contour line and an inner wall contour line. Generally, Outer wall contour line is sufficient. All curves retains all contours in the drawing (including inner and outer contours) and is generally not selected.

 

 

      • Bevel: If the part requires bevel processing, selecting Bevel will generate a bevel toolpath based on the original drawing. If this parameter is not available, you need to first go to the "Gear" in the upper-left corner of the software main interface User Settings → Machine Config  and select A axis bevel cutter for this parameter to be displayed. You can also refer to How to Enable Beveling for details on using beveling.

      • In-part shape: After selecting this option, TubesT can correctly recognize and process sheet-like parts that need to be nested in tube waste material. For specific cases, please refer to How to Process Nested Contours on the Tube Surface.

 

 

9. Identification Information (called Layer Mapping before 2026 V3)

 

Recognition Identifier: Sets whether to recognize identification information in the imported file. When selected, the software reads the identifiers in the file, and their processing method can be set to Marking, Inkjet Printing, or Not Cut. When not selected, identification information in the file is not read, and the processing method cannot be set.

Notice:

a. For identifiers in *.sat, *.stepx, *.step, and *.x2t files, Marking or Inkjet Printing can be selected.

b. For identifiers in *.t2t, *.nc1, *.rnc, and *.pcd files, only Marking is supported.

c. For *.jhb, identifier recognition is determined internally by the file and can be selected when drawing in TubeDraw. For details, please refer to  TubesT - Drawing Parts - Identifier.

 

 

Ⅲ. FAQS

 

1. How do I resolve an import failure?

 

Please refer to TubesT - How to Resolve Part Import Failures or Recognition Errors. 

 

2. How to use Import Excel sample file? 

 

Please refer to TubesT - Batch Import Parts Using Excel.

 

 

Baidu
sogou