2026世界杯足彩怎么买?2026美加墨世界杯足彩玩法说明与购买指南

TubesT - Island Co-edge
  • Software Download
  • Manual
  • Video
  • Tutorial
TubesT - Island Co-edge

I. Function Overview

 

The Island co-edge feature in TubesT refers to a situation where the cutoff lines of two parts are not completely identical. They share only a partial edge, leaving island scrap in the middle.

 

 

II. How to Use

 

1. Permission-related Information

 

(1) Starting from version 7.1.25, Island Co-edge is supported for angle steel and channel steel.
(2) Starting from version 7.1.29, the function of adding a lead line to the Island Co-edge has been added.
(3) Starting from version 7.1.39, Island Co-edge with part compensation is supported.

 

2. Notice

 

Three toolpath strategies are available for Island Co-edge in automatic nesting. You can select the appropriate strategy based on the actual processing requirements.

(1) Select 3-Segment Path only for symmetrical double-island cases to achieve a smoother and more visually appealing cutting sequence. For all other cases, choose either of the other two strategies.

(2) Select Continuous Path if it is a single island.

(3) Select Single Part Path if there are many or large islands, or the shared edge cutoff line is short.

Apart from the three specific situations mentioned above, Single part Path and Continuous Path each have their own advantages and either can be selected based on your processing requirements.

 

3. Parameter Definitions

 

① Single Part Path

 

First cut off the first part, and then cut off all island scraps to obtain the left cutoff line of the second part.
Advantages: It can be used in almost any situation. Especially when the final common edge line is short, the part is cut off with the first cut, so there is no need to worry about tube deformation caused by the tube rotating while still slightly connected to the part.

 

 

② Continuous Path

 

The toolpath starts from an island, and every island encountered is cut off first until the entire circle is finished.
Advantages: For a toolpath with only one island, the island can be cut first before cutting off the part, which is a continuous cut.

 

 

Disadvantages: If there are many or large islands and the cutoff line of the final cut is relatively short, the part may fall due to gravity before the final cut is completed, resulting in an uneven tear on the tube surface.

 

 

③ 3-Segment Path

 

Cut the island lines first, and then cut off the remainder with one cut.
Advantages: The cutting is continuous and smooth.
Disadvantages: The application scenario is limited to the case of two islands.

 

 

④ Add Lead to Island Co-edge

 

The start point of an island co-edge cannot be modified. If the piercing position on the island co-edge line after nesting is not ideal for piercing, a lead line technique can be added at the island co-edge line.
In the automatic nesting parameter interface, check the Add Lead option under Island Co-edge to add a lead line separately for the island co-edge toolpath.

 

 

The automatically generated nesting result will then have lead lines on the island co-edge toolpaths.

 

 

**Special Case 1
When adding a lead line to the nesting result, selecting the nesting result and using the Lead Line function will not change the already added Island Co-edge lead lines.

**Special Case 2
If the nesting result has been manually adjusted, the adjusted island co-edge will lose its lead line.

In addition, for nesting results without lead lines, it is also allowed to add lead lines separately.
Operation steps: Select the island co-edge line, click Lead Line, and set the lead line with an appropriate angle and length to add it.

 

III. FAQ

 

1. How to perform Island Co-edge for parts with compensation?

 

In versions prior to 7.1.39, the compensation of the island is lost when using island co-edge. If the software cannot be upgraded, it is recommended to achieve this through the following method: TubesT - How to Compensate Parts with Island Co-edge.

 

 

 

TubesT - Island Co-edge 155view

I. Function Overview

 

The Island co-edge feature in TubesT refers to a situation where the cutoff lines of two parts are not completely identical. They share only a partial edge, leaving island scrap in the middle.

 

 

II. How to Use

 

1. Permission-related Information

 

(1) Starting from version 7.1.25, Island Co-edge is supported for angle steel and channel steel.
(2) Starting from version 7.1.29, the function of adding a lead line to the Island Co-edge has been added.
(3) Starting from version 7.1.39, Island Co-edge with part compensation is supported.

 

2. Notice

 

Three toolpath strategies are available for Island Co-edge in automatic nesting. You can select the appropriate strategy based on the actual processing requirements.

(1) Select 3-Segment Path only for symmetrical double-island cases to achieve a smoother and more visually appealing cutting sequence. For all other cases, choose either of the other two strategies.

(2) Select Continuous Path if it is a single island.

(3) Select Single Part Path if there are many or large islands, or the shared edge cutoff line is short.

Apart from the three specific situations mentioned above, Single part Path and Continuous Path each have their own advantages and either can be selected based on your processing requirements.

 

3. Parameter Definitions

 

① Single Part Path

 

First cut off the first part, and then cut off all island scraps to obtain the left cutoff line of the second part.
Advantages: It can be used in almost any situation. Especially when the final common edge line is short, the part is cut off with the first cut, so there is no need to worry about tube deformation caused by the tube rotating while still slightly connected to the part.

 

 

② Continuous Path

 

The toolpath starts from an island, and every island encountered is cut off first until the entire circle is finished.
Advantages: For a toolpath with only one island, the island can be cut first before cutting off the part, which is a continuous cut.

 

 

Disadvantages: If there are many or large islands and the cutoff line of the final cut is relatively short, the part may fall due to gravity before the final cut is completed, resulting in an uneven tear on the tube surface.

 

 

③ 3-Segment Path

 

Cut the island lines first, and then cut off the remainder with one cut.
Advantages: The cutting is continuous and smooth.
Disadvantages: The application scenario is limited to the case of two islands.

 

 

④ Add Lead to Island Co-edge

 

The start point of an island co-edge cannot be modified. If the piercing position on the island co-edge line after nesting is not ideal for piercing, a lead line technique can be added at the island co-edge line.
In the automatic nesting parameter interface, check the Add Lead option under Island Co-edge to add a lead line separately for the island co-edge toolpath.

 

 

The automatically generated nesting result will then have lead lines on the island co-edge toolpaths.

 

 

**Special Case 1
When adding a lead line to the nesting result, selecting the nesting result and using the Lead Line function will not change the already added Island Co-edge lead lines.

**Special Case 2
If the nesting result has been manually adjusted, the adjusted island co-edge will lose its lead line.

In addition, for nesting results without lead lines, it is also allowed to add lead lines separately.
Operation steps: Select the island co-edge line, click Lead Line, and set the lead line with an appropriate angle and length to add it.

 

III. FAQ

 

1. How to perform Island Co-edge for parts with compensation?

 

In versions prior to 7.1.39, the compensation of the island is lost when using island co-edge. If the software cannot be upgraded, it is recommended to achieve this through the following method: TubesT - How to Compensate Parts with Island Co-edge.

 

 

 

Baidu
sogou